After any changes to setpoint limits, all setpoints in AUTO, MANUAL, BOOST, and HOLIDAY modes will be modified to conform accordingly.Ĭhange maximum setpoint temperature. The Digistat will switch on the heating if the temperature falls to 5☌ and maintains a temperature of 7☌ even when in OFFĬhange minimum setpoint temperature. Setpoint < room temperature – single low tone per 0.5☌ decrease Setpoint = room temperature – double tone Setpoint > room temperature – single high tone per 0.5☌ increase When enabled, audible tones indicate when the setpoint is more than, less than, or equal to the current room the temperature when a user manually adjusts the setpoint using the + button: Scroll through the different settings using the + and – buttons and press O to select and save. In the Installer Options menu (Fig 8), scroll through the options using the + and – buttons and press O to select. You can exit the menu by pressing until you have returned to the home screen. Use the + and – buttons to scroll to Installer Options and press O to select. This allows access to the User Menu 01, the Advanced User Settings Menu 02, the Installer Settings 03, and Service Interval Settings 04. To make changes to the default Installer Options shown below, enter the Installer Options menu by pressing the settings button for 3 seconds. Installation and Quick Start Guide 06490310001 Iss A INSTALLER OPTIONS The Digistat is now installed and will automatically start to control room temperature. Once paired the receiver LED will be solid green and the thermostat display will show the words PAIR REC for 3 seconds, before displaying current time and temperature.ĥ. While this short process is ongoing the receiver LED will lash green/amber and the thermostat will display the word SCAN. When the Digistat receiver is powered and the Digistat Thermostat has batteries inserted both will automatically pair. The boiler will fire for 1 hour or until the button is pressed again. Before pairing it is possible to test the wiring to the boiler by pressing the button on the receiver. As soon as the Digistat receiver has the power it will be ready for automatic pairing with the Digistat RF Thermostat. Replace the front cover of the receiver by locating the two latches at the top and then fasten the two screws at the bottom. The following options will appear in the Installer Options list:ġ0 Upper CH water set point 30-80☌ Default 70☌ 11 Lower CH water set point 10-25☌ Default 10☌ 12 Set DHW temp 45-70☌ Default 60☌ģ. Note that when connected to an OpenTherm boiler, Installer Options 06 Valve Protection and 08 Application Type are not available. Wire L and N from a separate supply with a 3A fuse. Connect the cables to the OpenTherm terminals OT1 and OT2 on the Digistat. Remove the OpenTherm cables from the existing controller or thermostat. If your boiler supports OpenTherm please follow these instructions: Always check other manufacturers’ instructions for compatibility. The receiver should be wired in to replace hard-wired room or programmable thermostats shown on the system or boiler wiring diagrams. The receiver should be wired to the combi boiler or central heating wiring using the correct type of cable or flex. This product is double insulated and does not require an earth connection. Fix the wallplate, terminals at the top, either directly onto the flat wall using wall plugs and no 6 x1” wood screws or on a flush-mounting single conduit box using M3.5 x 14 screws. Loosen the securing screws, remove the wallplate, and if surface wiring is to be used, snap out the cable entry strip on the bottom edge of the wallplate with a pair of pliers. Installation of the wallplateįixing (minimum wallplate clearances shown below) Warning: Installing the receiver too close to the metal side panel or mains cables may interfere with the radio signal. It is recommended that the receiver is mounted on the wall nearest the final location of the Digistat Thermostat room thermostat and not less than 30cm from the boiler side panel. #Drayton mistat wireless room thermostat installFor the best performance install in an open space, at least 30cm distance from any metal objects including wall boxes and boiler housing. (Care should be taken not to mount the receiver in a position where it is surrounded by metal objects or mains voltage cable, as this may interfere with the radio signal). The Digistat Receiver should be mounted in a convenient position, close to the boiler or central heating system wiring center.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |